Cold room user manual
1. INSTALLATION
1.1 Panel Installation
The panels have an eccentric hook locking mechanism system and the floor panels have their own
between each other, wall panels among themselves and ceiling panels among themselves
can be locked together. Inside-outside corner-edge junctions
accessories are used.Cold room Installation can be done by following the steps below.
To be installedFloor panels of the Cold Room amongst themselves
are combined by locking. Then, "U" accessories where the wall panels will sit
The floor panel is turned around and fixed to the floor where the room will be installed.
The wall panels are locked together sequentially within the fixed accessories.
is placed. Wall panels corner joints, using interior accessories
are fixed together.
The ceiling panels are interlocked onto the installed wall panels.
is placed. The inner edges of the panel room are sealed using internal accessories.
is provided.
Cold roomAfter the installation of the panels, interior and exterior accessories are completed and
To ensure sealing, silicone is applied to the accessory joints and
The installation is completed by inserting the plugs into the hook locking holes.
1.2 Cooling Device Installation
Cold roomcooling devicesin generalMonoblock and split device including two
is the type.
Monoblock cooling devicescold roomceiling panels at installation stage
It is mounted on the wall panel by passing it from the top before being placed.
Split cooling devices consist of two parts: indoor and outdoor units. indoor unit
vaporizercold room is mounted inside. outdoor unit condenser cold room
It is installed in a ventilated area or outdoors. two units
Copper piping and communication cabling are made between them.
Measure the mains voltage before connecting the power supply to your machine,
Check whether grounding is done. Only use the cooling device
Use if the values match the values of the product. Otherwise, your machine
parts may be damaged.
3
1.3. Regular Electrical Voltage
Electrical voltage should be regular and constant (220V or 380% 5%)
must. Our company is not responsible for any disorders arising from this situation.
1.4 Installation and Commissioning;
a. Choosing the appropriate place to place the cold room
It is a factor that directly affects operating performance and electricity consumption.
It is sized according to the type and quantity of goods to be placed in the cold room.
Cooling device cooling capacity,cold room The type of goods to be placed inside,
It should be chosen to respond to the amount and daily loading capacity.
Your Cold Room the location where the split cooling device outdoor unit will be installed,
distance between ventilated space or outdoor max. 25 meters
should be. Otherwise, the cooling performance of the cooling device will decrease.
Cold Room The place where it will be installed must have a flat and level ground.
should be
As far as possible from devices, tools and equipment that produce heat
position it.
Be careful not to place it in places that receive direct sunlight.
b. Before starting for the first time, do a general cleaning. Soapy water for cleaning
you can use
c. Before using the device fully, leave it empty for 24 hours.
Run until .Cold roomIt is ready for use when it reaches the desired temperature.
However, you should always load your closet at once.
This causes the cooling device compressor to fatigue and decreases performance.
will shorten its lifespan.
d. Cold Roomtemperature decrease and increase of the digital thermometer
The response time may not be the same as the change in the internal temperature of the cabinet. This
Therefore, you need to wait for a while to understand the real temperature values.
It is.Cold room The temperature sensor of the digital thermometer inside the cabinet
It is located near the upper area.Cold roomthe temperature inside
may differ, the temperature in the upper regions and the temperature in the lower regions
The difference may be 1-2 degrees. That's why you want the products you want to stay cooler.
You can put it at the bottom of the refrigerator.
2. USE
Cold room After preparing it as stated in the 'First Operation' section,
You must intervene outside of digital control to ensure its continuation.
It is not necessary.
2.1 Operating the Cooling Device;
Turn the on/off switch on the control panel to “I” or
Turn it to "ON" position.
You can read the temperature set value of the digital display next to the on/off switch.
Set it to the desired value.
2.2 Stopping the Cooling Device;
Turn the on/off switch to "0" or "OFF" position.
2.3 Rules to be Considered;
To obtain the best performance, do not place hot foods in the cold room.
Do not put it.
The daily loading capacity of the cold room is very large, such as food and beverages at a time.
Do not load items by placing them at the same time. This cooling time
It will increase the compressor's hard work and fatigue, thus shortening its life.
It will shorten and electricity consumption will also increase.
Do not leave the doors open, avoid opening them frequently as much as possible.
In order to increase the performance of the cooling device and reduce electricity consumption, certain
periodically (e.g. once a week) to remove any ice that has formed on the cooler parts.
melting by pressing the manual melting button or
You need to turn it off with the switch and wait until the ice thaws.
3. MAINTENANCE
3.1 Protection;
Clean the device with soapy water before first use. Cleaning that abrades the surface
Do not use materials. Clean the exterior of the device regularly. of your machine
Since the motor group and fan will be negatively affected by dust in the ambient air,
Pay attention to cleanliness, be careful not to use your machine in dusty environments.
show.
5
3.2 Care;
Maintenance must be performed by authorized technical personnel. Chiller group and condenser
lamellae should be cleaned. Cleaning frequency depends on environmental cleanliness.
3.2.1 Periodic maintenance;
Before performing some operations, turn off the main switch and de-energize the device. Device
Visually inspect the parts. Periodically inspect part components at least once a year.
Please check once.
3.3. Cleaning
Before starting cleaning, cut off the power of the device by turning off the fuse.
You can clean the device by wiping it with soft objects (cloth, sponge, etc.).
Clean the body of the device, paying attention to the electrical parts.
Be sure to clean the device after using chlorinated substances.